K5DS-SP and K5DS-RC

Splitter and Receiver for DSNet Signage Broadcast Network

DSNet splitter and receiver
  • Main Features

  • Overview

  • Technical Spec.

  • Technical Support

  • Networking Devices for DSNet
  • Support 300m UTP cables
  • The receiver can drive two monitors
  • Cable amplification, compensation and deskewing
  • Light and contrast video settings
  • Volume and stereo-balance audio settings
  • Transparent to the monitors
  • Bidirectional RS232 connections up to 115200 bps with management signals.
  • Metal housing
  • One year warranty and free technical support.

The K5DS-SP splitter and the K5DS-RC receiver are high performance networking devices allowing to build DSNet networks when used with the K5DS-BR broadcasters.

K5DS-SP is useful in large configurations. It amplifies, restores, and forwards to 8 output ports, the audio, video, and data streams received from the input port. The purpose of K5DS-SP is to increase the number of monitors connected to the broadcaster. With one tier of splitters, the number of display panels connected to a single K5DS-BR can increase from 160 to 1024, and with two tiers of splitters it can pass to 6144. K5DS-SP also retransmits all data received from the monitors to the broadcaster.

DSNet receiver connection

K5DS-RC is a long haul 300m receiver able to connect two monitors. Thanks to their chaining port, the receivers can be wired in series. The two RS232 ports can exchange bidirectional data with the broadcaster at data rates up to 115200 bps.

For each monitor you can tune the following settings in a few mouse clicks:

  • Cable compensation
  • Cable RGB deskew
  • Video contrast
  • Video brightness
  • Audio volume
  • Audio balance
  • RS232 settings
  • Unidirectional or bidirectional RS232
Note :
All settings are sent by K5DS-BR to the receivers and splitters across the Cat5 cables. K5DS-RC and K5DS-SP don't have any archaic setscrews that require you to risk your life climbing a ladder with a screw driver, and that are deregulated the next day.

The video and audio settings can be easily set in a few seconds looking at the display panels and moving the sliders of DSNet Management until the result is perfect. All settings are digital and saved into EEPROMs.

If this is a large installation, and if the display panels are far from an Ethernet access, we recommend you run DSNet Management on a laptop featuring a wireless interface or 3G key. By this way you can access to the broadcaster Management Server over the local network or over the Internet.

 

Splitter
Cable

Recommended cable: UTP Cat5

Supported cable: UTP Cat5, UTP Cat5e, UTP Cat6

Max delay skew between pairs: 60ns

Max attenuation: 52 dB at 50MHz

 

Back Panel

DSNet splitter back panel

 

 

Front Panel

DSNet splitter front panel

 

 

Indicators:

  • Power
  • System In: Lights on if the splitter is enabled.
  • For each System Out Port: Lights on if the output port is enabled.

 

Note: Disabled ports receive and drive no stream.

Video Resolution

1920 × 1080 @ 60HZ over 300m.

Higher resolutions are possible with shorter cables.

Management

Via the broadcaster with DSNet Manager software.

Power Supply

External 5V 2A power adapter

Working temperature

0 to 50°C

Stocking Temperature

-20 to 60°C

Humidity

0 to 90%, not condensing

Housing

Metal case

Dimension (L x l x H)

130 x 135 x 40 mm

Weight

600 g

Standards

FCC, CE

Ordering Information

K5DS-SP8 : 8-port DSNet Splitter

 

Receiver
Cable

Recommended cable: UTP Cat5

Supported cable: UTP Cat5, UTP Cat5e, UTP Cat6

Max delay skew between pairs: 60ns

Max attenuation: 52 dB at 50MHz

 

Back Panel

DSNET Receiver back panel

Back Panel Connectors

 

System Out: Chaining port for serial wiring.

Audio: Stereo audio port to monitor 2

VGA: Full VGA interface to monitor 2

RS232: to monitor 2. Up to 115200 bps, RTS/CTS, DSR/DTR


Back Panel Indicators

Power

System Out: Lights on if the chaining port is enabled, i.e. indicate if next receivers can receive the video, audio and data streams.

Front Panel

 

DSNet Receiver front panel

 

Front Panel Connectors

System In: Connection to broadcaster, splitter or previous receiver.

Audio: Stereo audio port to monitor 1

VGA: Full VGA interface to monitor 1

RS232: to monitor 1. Up to 115200 bps, RTS/CTS, DSR/DTR

Front Panel Indicator System In: Lights on if the receiver is enabled.

Management

Via the broadcaster with DSNet Manager software.

Power Supply

External 5V 2A power adapter

Working temperature

0 to 50°C

Stocking Temperature

-20 to 60°C

Humidity

0 to 90%, not condensing

Housing

Metal case

Dimension (L x l x H)

130 x 135 x 25 mm

Weight

540 g

Standards

FCC, CE

Ordering Information

K5DS-RC2 : Long-Haul 2-Monitor DSNet Receiver

 

pdf Datasheet

In case of problem contact:

email: support@prosum.fr

telephone: (33) 1 4590 6270